Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4740
Results: 4740
Philco Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO | PH42M30 | Stand bye LED lights up dimly and doesn't turn on | Ci regulator 3.3v n805, measuring 2.5 volts | Replace | HP ELETRONICA |
| PHILCO | TPF2922 | It doesn't turn on, the stand by LED keeps flashing, | Replace cap ,c927 ,2,2x100v e c943 10x100v | DJ PITUKA | |
| PHILCO | PH42M61DSG | Turns on, the philco logo appears and then it gets stuck at the message "initializing, please wait..." | 3.3v regulator (n105) changed with 1.7v only. | It appeared to be a software defect, but the nand memory had already been replaced and the defect continued. | MLTOLOI |
| PHILCO | 21MSS | It turns on normally, when we press power the LED goes off, the screen flashes and returns to stand bay. | In my case it was the flyback leaking. | Swapped the flyback and the TV worked normally. | Rdo Antônio Acre |
| PHILCO | TPF2130 | Image blurs and turns off after a few seconds | Rusty tube socket | Replace tube socket | Joao paulo |
| PHILCO | TV PH21SS | Horizontal with bands on the sides (6 to 7 cm, about 3 fingers). | Replace the rp551 and a regulated three-way power supply | SEVERINO G 20 | |
| PHILCO | PTV32D12D | Sound escaping or no audio. When I picked it up it already had no sound. | Open smd ca23 capacitor close to the audio i.c. | I put a 200nf taken from another board. the sound appeared again. | sammolacerda |
| PHILCO | TPF2940 | It turned on normally but tsound was no white drizzle, it had normal characters and the sound of the channel but tsound was no image just this black screen. | In my case the fly-back burst and sparked everywsound, burning r714 and changing r724, leaving the c731 smd shorted which also opened r723 smd | Replace all the components mentioned good luck ass:edfesom | Edfesom |
| PHILCO | PH21C | It only turns on if the board heats up | Ic 801 just trace | Jr eletrônica | |
| PHILCO | TP2010 | TV turns on with a vertical line in the middle of the screen and turns off and the LED blinks | R709 amended | R709 amended | Eletronica Line Jatoba ma-org-Cicero l |
| PHILCO | PH14 ULTRA SLIM | Goes into protection with noise in the flyback | C450 marked 681 (680pf) | Replace | Eletrônica Mauro Mascarenha - Parazinho Ceara - Tel : (88)981422821 |
| PHILCO | PH200 | Does not turn on secondary dead | In my case it was the audio output | Replace everything | eletronica sto ant rj bahia |
| PHILCO | PH42M61 | Só stand by | N805 regulator (near the processor) just change it, I mean in my case it was it and I hope it's yours too. | Bruno Nicácio | |
| PHILCO | PH29USA2 | Screen with colors shuffled like a rainbow | Ptc of the kinescope magnetizer defective. | After changing the ptc, the perfect image returned to normal. | Everton Moscato |
| PHILCO | PH14C 20C | Sound 0 mute 1 full volume. | After copying several memories, it can only be resolved by changing the data. | Menu 6483, mute, up to m2, setup celect to 1, mute up to m6, v. max from 46 to 63, mute m9, balance from off to on. sir stand by | George Pontes |
| PHILCO | TP2920 | It connects with the magnetized tube and has a colored wheel in the middle of the screen. | Rl1 | Replace the rl1 relay | Sinailson furtado |
| PHILCO | TP2920 | Turns on with retrace lines at the top of the screen and the vertical closes and the TV turns off. | C1 | Replace o capacitor c1 100μF25v | Sinailson furtado |
| PHILCO | PH21USA1 | Low noise at the power supply, all low power supplys, +b 60 and a few v. does not start. | R 553 from 5k6 altered for 13k .trimpot 2k aberto | Replace these components. | J B Eletron |
| PHILCO | PH21MSS | League. no signal and when you put in the antenna cable everything goes dark | Ci memory | Defective memory ic. just run for the hug | Eduardo santos |
| PHILCO | PH32M3 LTA320AN01 | Turns on, shows the logo and turns off the backlight, leaving only the sound and the image in the background without light. | Strong burning smell, I opened the screen and found that tsound was a light bulb sparkling. | The lamp connector was sparking. I replaced it and it resolved. Tip for everyone: when disassembling LCD TVs, keep the lamp connectors ;) | PL Eletrônica |