Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4740
Results: 4740
Philco Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
DVD PHILCO | PH154 | Turns on and blows fuse immediately | After checking the rectifier bridge I discovered that it was the ci u1 on the board, I just changed it and ran to dim dim | ELETRONICA PUBLISOM DE NATAL RGN | |
PHILCO | PH23F33D | Sound failing. After several minutes, tsound is no sound. | C602. | jr_TEC | |
PHILCO | MSS MSS | With normal image only at the bottom - everything is dark above | Causing the electro capacitor - 303 of 470.uf - close to the vertical ci- | Just replace and move on to another cucumber - resonant electronics claudia mt- | Raimundo damascena |
PHILCO | TP2920 | Inoperative standby LED does not turn on | Ic901 | When placing the finger on the IC901, the power supply activates and the stand bay LED lights up. Just replace the ic901 and the TV will work normally. God be praised! | Sinailson furtado |
PHILCO | TP2920 | Normal turns on the menu characters appear as normal but the image does not appear and the screen remains dark. | A rabble | Replace the 4k7 r723 and the TV will work normally. God be praised! | Sinailson furtado |
PHILCO | PH800M DM1001-SE.PCB | Turns on, but no sound, normal outputs. (tda7498e) | Electrolytic capacitor ce37(47uf/50v) shorted activating mute circuit. | MLTOLOI | |
PHILCO | PH200 | Sometimes it turns on with a flashing display or just a blue LED on volume | Lack of 3v3 in the supply measure pin 8 eeprom if it is low the defect is tsound | 3v3 regulator | beto2828 |
PHILCO | PH32E31DG | No image after a while on | R2b0 20k changed | Put 22k go for the hug | PS eletrĂ´nica |
PHILCO | PH24D20DG | The TV turns on, no image appears and returns to stand by | 12v zener on the screen ruler, it is after the fuse | Mariano | |
PHILCO | PH32E32D | Does not come out of the usb screen | Use buster control to exit | MARIANO | |
PHILCO | PH42M61DSGW | Does not tune channels | Changed 3.3v regulator n105 | wkeletronica (47)99636-9908 | |
PHILCO | PMS24 | Oven turned off after 2 seconds. I turned off the clock and reset the time. | After changing the board the defect persisted. I deduced that it would be magnetic interference. | Loose magnetron and high voltage diode screws, causing sparking. I just squeezed them and went for a hug. | Alexandre Oliveira |
PHILCO | PTV 32E20DSGWA | Locked | Corrupt software - write to a pendrive | The TV does not have a power button, so press the SW1 key on the board and connect the TV to the socket. (already with the flash drive with the update) | PardalX |
PHILCO | PH21US A1 | Secondary voltage varying and LED flashing | After a lot of research I found r512 from 6k8 changed to 8k and varying between 9k.7 | Replace r512 | junior |
PHILCO | TP20V56 | It doesn't turn on, it just stays on, the LED is on | When you press the switch, the LED flashes, the voltage does not arm and drops, the vertical stv9302a is defective, I replaced it and the electrolytic capacitor with its capacity depleted c918 and c914 - 1000ud 16v | Defect resolved | Andre |
PHILCO | PH32E63D | I'm sound | Software | Sw update (update menu password 0812) | Brackmann (51)997366096 |
PHILCO | PH14D | Image moved to the right side of the screen | Replace capacitor c406. | RAIMUNDO | |
PHILCO | PH42E53SG | Inverted image | With the TV on, type: 062.598.menu.005 or 006 | Persio(TVCompany) | |
PHILCO | PH21MSS | Greenish image | Defective image tube a51cpac00x01, I changed the image, it came back in color | Defect resolved | Andre |
PHILCO | PH28S63D | League has sound no image | All the LEDs shorted, I replaced them all and I also changed the power supply to a toasted L6 coil and leaky MOSFET, the original is not sold. | Defect resolved | Carlos |