Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4740
Results: 4740
Philco Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | PH400 | Doesn't start | Capacitor 1000µ por 16v | Ec25 1000µ 16v | MArcelo Piranga |
PHILCO | PH21MG SS | The TV turns on but the image is not complete on the sides (cup type) and retrace lines on the top | La78141 broken. replaced and problem solved. | Carlão | |
PHILCO | PH42E53SG | TV doesn't turn on, doesn't have 3.3 volts | Zener diode d 203 of 18 returns short | multsom | |
PHILCO | PH400 | Low sound, but everything works. You can barely hear it, even with the volume turned up to maximum. | In this case it was IC8, an 8-terminal IC, close to the DVD motor connections | Replace the ic8: f16-100 hip | Romildo Behrend Schwartz |
PHILCO | PH400 | The device doesn't turn on, it just turns blue on the front, on the volume button, but it doesn't activate anything. | It was discovered that it was a diode, which is on the IC side of the DVD motor drive, wsound tsound are 3 in the middle of 2 larger transistors: d33 | Replace the d33, even if it is good in terms of measurement | Romildo Behrend Schwartz |
PHILCO | PH400 | The blue volume LED keeps flashing and the device does not turn on. the 5v and -21 power supply is oscillating, below what it should be. | After much research, it was found that the 33nf capacitor cb8 was responsible. | Replace for another good one, even if it doesn't show a defect. It is close to the photo coupler and the DVD motor connections. | Romildo Behrend Schwartz |
PHILCO | PH46 | Intermittent image disappears, back light comes on and tsound is sound. | Principle out lvds | At first, replace the lvds cable or remove it and clean the contacts that go to the tcom board with wax and retighten the connectors on the main board. it was a show. | ALEX LOPES |
PHILCO | PH29M-SS | The power signal enters protection, high power supply | D404 shorted feeds 200v tube plate | Replace d 404 | af-sat eletronica |
PHILCO | TP2920 | It doesn't turn on, pressing power turns off the LED but it doesn't oscillate, | Replace resistor,r715 ,1k8 ,2w | DJ PITUKA | |
PHILCO | : PH23F33D | When turning on the TV, the sound is normal for about five minutes, the sound starts to fail and then tsound is no audio | Resolda o capacitor 602 | Run for a hug | Laerte |
PHILCO | PH1454 (P) | Image with waves | Varicap | Replacement | EletroClaudio |
PHILCO | PH32 LED A4 | Turns on but the LEDs do not light up, only the power LED changes from red to green | All voltages were ok | Memory recording with new software | CENTRO DIGITAL ELETRONICO |
PHILCO | PH21MSS | Stand by access, the LED flashes, but it does not start, tsound is a hissing sound at the power supply | R804, ic801 e o capacitor c803, 220nfx400v | Gracielia | |
PHILCO | PH21USA1 | Vertical closed | Ci vertical stv original | Tda8172 substitutes | eletronica mauri junior |
PHILCO | PH21M PH21M | Turns on vertically closed then turns off/on and when working turns off LED keeps flashing | Cold solder on pin 3 of ci la78 141 this pin is the one that goes directly to the deflector | After resolving it worked normally | LUIS VICENTE |
PHILCO | PH40R86DSGW | When turned on, it appears as normal, brightly lit... after that the image becomes very dark, you can only see the image with the ambient light turned off. | 4 defective LED bars, each ruler with a burned out LED! | José técnico | |
PHILCO | PCM1444 | The TV has a black and white image. The voltage at pin 48 on the computer fluctuates at 5V | Problem with output 48 of the micro palm-m | Replace capacitor 117 1mf/50v. | DANGRA ELTRÔNICA SÃO PAULO |
PHILCO | PH14 GAME OU ULTRA SLIM | No audio. | 100k r603, open. | Replace r603 of 100k and move on to the next one. | Carloscte |
PHILCO | PH21M SS | Vertical closed about 2 fingers in the middle and appears to be a bad deflector coil, | Diode d301 1n4007 which only shows a defect in the circuit, on the analog multimeter on the highest resistance scale it shows good! | Replace it for sk1/08 | Fernando Alcantra |
PHILCO | PH32M2/M3 | Power supply takes time to arm and switch on standby. | Check 20v power resistors on q6 4401. | The glue may be interrupting, re-solder the resistors. | Eronaldo(erontec) |