TV Repair: Common Faults and Solutions.
Search:
Results: 87413
Results: 87413
Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
SONY | KV1543R | No remote function, replaced ic001 | Remote does not work, manual ok. | ||
SONY | KV9300 | No control of brightness | No control of brightness, excessive brightness even withscreens and drives down, voltages ok in abl drive circuits. also incolor. | ||
SONY | KV8000 | Incorrect brightness operation with retrace lines | Excessive brightness and retrace tube cathode voltages low,10v. | ||
SONY | KV2643R | No sound or picture, replaced ic2002 | No sound or picture. could not program any channels norwould the set change address positions. | ||
SONY | KV2643R | Incorrect channel indication | The channel indicator neon lamps are polarized and will notlight when soldered in backwards. the lamps are not marked as to whichway they are to be soldered in. | ||
SONY | KV2101 | Poor v linearity, r517 increased in value | Poor vertical linearity top 1/3 of picture slightlycompressed. vertical size control to end of range. waveform at base ofq501, blanking pulse 5 msec, it should be 1.2 msec. | ||
SONY | KV1714 | Dead | Dead set, 1.6 amp fuse blown, horizontal out transistorshorted, b+ regulator shorted. | ||
SONY | KV1543R | Intermittent shut down, replaced r532 | The set would intermittently shut down. | ||
SONY | KV1201 | No color, resoldered r356 | No color. checked cw signal at the collector of q307 whichwas not there. signal was present at the base. i checked the dcvoltage - collector was 18v, that told me that the transistor was notconducting. base voltage was normal (3v) emitter was 2.8v. | ||
SONY | KP5000 | Green picture, replaced c323 | Severe bright green screen no control. | ||
SONY | KP5000 | Shut down, replaced c5112 | Immediate shut down - no high voltage. | ||
SONY | KP5000 | Dead, bushing on vert output was carbonized | Unit cannot be turned on. when the power switch is activated,unit comes on for 2 seconds and goes off. checked and f6103 was foundopen. 120v line was loaded. when i checked resistance from 120v b+ toground, i read 150Ω both ways. ga-9 (plug) pin | ||
SONY | FX310 | No audio | No audio - any function. acts like bad function switchbecause if applied additional pressure on knob volume works - releaseknob - no audio. | ||
SONY | TPSL2 | Defective motor | Tape player would not run. motor seemed to draw excesscurrent. a check of the motor revealed the fg winding was shorted to themain winding. | ||
SONY | TPSL2 | Weak battery spring | Customer complaints of wow while tapping the unit (i found 4units with the same problem). | ||
SONY | TCM280 | Misprint in s/m | On page 23 of tcm-280/280b service manual a part numbermisprint exists. -hq comments: the correct part numbers for two diodes are as follows:dm-101 8-745-101-01dm-101a 8-745-101-11the dm-101 substitutes for the dm-101. thus, in this case, the part | ||
SONY | TCK96R | Connection error in manual | The connection point shown for the white wire is incorrect.this should go to the other end of r719. the wiring diagram in themanual supplement #2 is not clear on where this wire connects. also, theblack jumper wire and r707 to the connecting point of t | ||
SONY | TCK96R | Open d604 | Unit will only go into fwd plays - all other modesnonfunctional. | ||
SONY | TCK71 | Alignment of tape path | Found back tension 3.5 gcm and tape path high at pinch rollerand low at head, causing tape wrinkle. | ||
SONY | TCK61 | Missing 2.5mm steel balls | The head deck assy will not move fully into the cassette. inthe case of the tc-k81, the assy jammed in the cassette case, chippingthe erase head. |