TV Repair: Common Faults and Solutions.
Search:
Results: 87413
Results: 87413
Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
SONY | KV2645R | Snow picture, replaced bt981 prescaler | Unit goes to snow. substituting tuner didn't cure problem.voltages around front end seems to be at spec. tried prescaler andthat solves the problem. | ||
SONY | KV2645R | Poor remote operation, replaced q1 | Remote would operate intermittently and is usable up to6 feet from cabinet. q1 on head amp board noisy - collector voltage onq017 on md board was varying between 4 and 8 volts. | ||
SONY | KV2601 | Snow picture, replace c209 | Snowy picture on all channels. uncontrollable rf, agc:measuring dc potential at pin 5 of ic201 (cx555) netted approx. 2.5vdcwith no change upon varying rf agc potentiometers. measuring c209 outof circuit yielded approx. 20 microamperes leakage. | ||
SONY | KV1945R | Incorrect tuning operation, replaced zener d008, q006, q008 | Unable to tune any vhf/uhf stations. | ||
SONY | KV1945R | Poor remote operation, replaced c4 | The range of the remote control was no more than about 8 feet. there was excessive noise seen at output of n board, remote amplifier. | ||
SONY | KV1913 | Dead | Came dead with shorted horizontal output and fuse. replaceparts, plug to variac and slowly raised line voltage. current wasexcessive showing short on the circuit, but doesn't show on theΩmeter.found bad flyback. | ||
SONY | KV1545R | No tuning, replaced pre-scaler | No signal on any channel except sound on ch. 13 only. ifexternal voltage was introduced to vc line i could get some of the highband channels, which indicate tuner was good. | ||
SONY | KP7220 | Insufficient width, replaced ic-2003 "k" board | Unit suddenly had insufficient width to fill the screen.voltage on 115v regulator on k board was about 10 volts low. | ||
SONY | KP5000 | Poor purity | Color purity problems around edge of picture. problem was caused by flaking of phosphor edges on all three crts. | ||
SONY | KV2645R | Incorrect operation, replaced x002 | When master power switch turned off and unit allowed to cooldown, it would take approx. 2-3 hours for any function to operate afterapplying power. cooling the ceramic osc. x002 would cause unit to shutdown and all functions became inoperative. | ||
SONY | KV2645R | Picture dark with excessive color, replaced r-751 | Color overload or flaming color. color was especially extensive mostly in the red spectrum. even when the color was turned down, some overload still existed. | ||
SONY | KV1945R | No audio, replaced open r232 and shorted q205, q206 | Not audio. | ||
SONY | KV1942R | Tuner drifts, replaced zener d2103 | Tuner drifts off channels and several lights are lit at thesame time. 18 volt line to tuning circuits would be low, about 10 vdc,and problem would occur. d2103 was zenering at lower voltage causing18v line to drop. | ||
SONY | KV1913 | Dark picture | Dark picture. | ||
SONY | KV1913 | Sound distortion | After warm-up sound would distort and change in volume. | ||
SONY | KV1714 | Set locks on ch 2 | Set locked on ch. 2 defective cx804 (ic033) decreasing 35vsupply. | ||
SONY | KV4000 | No tuning on vhf low | No automatic nor manual tuning on vhf low, vhf high anduhf band. found no voltages at vc terminal of tuner - resistancemeasurement showed short to ground - tracing back found short at m1 plugon m board - pin 8 shorted to pin 9. | ||
SONY | KV2645R | Snow picture, replaced x001 | Intermittently, tv reception would stop except for a verypoor channel 6, snow on all other channels. address line a always high(11.9v) regardless of channel selected. | ||
SONY | KV2643R | Picture shifts, demagnetized crt | Graphics were shifted to the right. when unit was taken toservice shop and center-cross generator placed on set the centering wasoff approx. 2 inches to the right. all associated circuitry was checkedand found to be in proper operating condition. repl | ||
SONY | KV2643R | No picture, replaced c607 | The following parts were bad in this set: q901, q902, q601,r605 open, r609 open, r232 open, connector a-10 on pc board arcing.after all these parts were replaced, the set would come on and thepicture would blink severely, both horizontally and verticall |